[Allocatable] = [Node Capacity] - [system-reserved] - [Hard-Eviction-Thresholds]
To provide more reliable scheduling and minimize node resource overcommitment, reserve a portion of the CPU and memory resources for use by the underlying node components, such as kubelet
and kube-proxy
, and the remaining system components, such as sshd
and NetworkManager
. By specifying the resources to reserve, you provide the scheduler with more information about the remaining CPU and memory resources that a node has available for use by pods.
CPU and memory resources reserved for node components in OpenShift Container Platform are based on two node settings:
Setting | Description |
---|---|
|
This setting is not used with OpenShift Container Platform. Add the CPU and memory resources that you planned to reserve to the |
|
This setting identifies the resources to reserve for the node components and system components. The default settings depend on the OpenShift Container Platform and Machine Config Operator versions. Confirm the default |
If a flag is not set, the defaults are used. If none of the flags are set, the allocated resource is set to the node’s capacity as it was before the introduction of allocatable resources.
Any CPUs specifically reserved using the |
An allocated amount of a resource is computed based on the following formula:
[Allocatable] = [Node Capacity] - [system-reserved] - [Hard-Eviction-Thresholds]
The withholding of |
If Allocatable
is negative, it is set to 0
.
Each node reports the system resources that are used by the container runtime and kubelet. To simplify configuring the system-reserved
parameter, view the resource use for the node by using the node summary API. The node summary is available at /api/v1/nodes/<node>/proxy/stats/summary
.
The node is able to limit the total amount of resources that pods can consume based on the configured allocatable value. This feature significantly improves the reliability of the node by preventing pods from using CPU and memory resources that are needed by system services such as the container runtime and node agent. To improve node reliability, administrators should reserve resources based on a target for resource use.
The node enforces resource constraints by using a new cgroup hierarchy that enforces quality of service. All pods are launched in a dedicated cgroup hierarchy that is separate from system daemons.
Administrators should treat system daemons similar to pods that have a guaranteed quality of service. System daemons can burst within their bounding control groups and this behavior must be managed as part of cluster deployments. Reserve CPU and memory resources for system daemons by specifying the amount of CPU and memory resources in system-reserved
.
Enforcing system-reserved
limits can prevent critical system services from receiving CPU and memory resources. As a result, a critical system service can be ended by the out-of-memory killer. The recommendation is to enforce system-reserved
only if you have profiled the nodes exhaustively to determine precise estimates and you are confident that critical system services can recover if any process in that group is ended by the out-of-memory killer.
If a node is under memory pressure, it can impact the entire node and all pods running on the node. For example, a system daemon that uses more than its reserved amount of memory can trigger an out-of-memory event. To avoid or reduce the probability of system out-of-memory events, the node provides out-of-resource handling.
You can reserve some memory using the --eviction-hard
flag. The node attempts to evict
pods whenever memory availability on the node drops below the absolute value or percentage.
If system daemons do not exist on a node, pods are limited to the memory
capacity - eviction-hard
. For this reason, resources set aside as a buffer for eviction
before reaching out of memory conditions are not available for pods.
The following is an example to illustrate the impact of node allocatable for memory:
Node capacity is 32Gi
--system-reserved is 3Gi
--eviction-hard is set to 100Mi
.
For this node, the effective node allocatable value is 28.9Gi
. If the node and system components use all their reservation, the memory available for pods is 28.9Gi
, and kubelet evicts pods when it exceeds this threshold.
If you enforce node allocatable, 28.9Gi
, with top-level cgroups, then pods can never exceed 28.9Gi
. Evictions are not performed unless system daemons consume more than 3.1Gi
of memory.
If system daemons do not use up all their reservation, with the above example,
pods would face memcg OOM kills from their bounding cgroup before node evictions kick in.
To better enforce QoS under this situation, the node applies the hard eviction thresholds to
the top-level cgroup for all pods to be Node Allocatable + Eviction Hard Thresholds
.
If system daemons do not use up all their reservation, the node will evict pods whenever
they consume more than 28.9Gi
of memory. If eviction does not occur in time, a pod
will be OOM killed if pods consume 29Gi
of memory.
OpenShift Container Platform supports the CPU and memory resource types for allocation. The ephemeral-resource
resource type is supported as well. For the cpu
type, the resource quantity is specified in units of cores, such as 200m
, 0.5
, or 1
. For memory
and ephemeral-storage
, it is specified in units of bytes, such as 200Ki
, 50Mi
, or 5Gi
.
As an administrator, you can set these using a custom resource (CR) through a set of <resource_type>=<resource_quantity>
pairs
(e.g., cpu=200m,memory=512Mi
).
For details on the recommended system-reserved
values, refer to the recommended system-reserved values.
Obtain the label associated with the static MachineConfigPool
CRD for the type of node you want to configure.
Perform one of the following steps:
View the Machine Config Pool:
$ oc describe machineconfigpool <name>
For example:
$ oc describe machineconfigpool worker
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfigPool
metadata:
creationTimestamp: 2019-02-08T14:52:39Z
generation: 1
labels:
custom-kubelet: small-pods (1)
1 | If a label has been added it appears under labels . |
If the label is not present, add a key/value pair:
$ oc label machineconfigpool worker custom-kubelet=small-pods
Create a custom resource (CR) for your configuration change.
apiVersion: machineconfiguration.openshift.io/v1
kind: KubeletConfig
metadata:
name: set-allocatable (1)
spec:
machineConfigPoolSelector:
matchLabels:
custom-kubelet: small-pods (2)
kubeletConfig:
systemReserved:
cpu: 1000m
memory: 1Gi
1 | Assign a name to CR. |
2 | Specify the label from the Machine Config Pool. |